BMK2 new series motor adapt the advanced Geroler gear set designed with disc distribution flow and high pressure. The unit can be supplied the individual variant in operating ultifunction in accordance with requirement of applications.
* Advanced manufacturing devices for the Geroler gear set, which use low pressure of start-up, provide smooth and reliable
operation and high efficiency.
* The output shaft adapts in tapered roller bearings that permit high axial and radial forces. The case can offers capacities of
high pressure and high torque in the wide of applications.
* Advanced design in disc distribution flow, which can automatically compensate in operating with high volume efficiency and
long life , provide smooth and reliable operation.
* The new series motor is suitable for vehicles with greater loads and pressure drop.
BMK2 Hydraulic Orbit Motor
|Type||Geometric displacement (cm3 /rev.)||Max.speed
* Continuous pressure:Max.value of operating motor continuously.
* Intermittent pressure:Max.value of operating motor in 6 seconds per minute .
* Peak pressure:Max.value of operating motor in 0.6 second per minute.
BM Series Orbit hydraulic motor product manual
1. Matters needing attention
1.1 Output steering
1.2 The correct use of the motor will directly affect the working life. Therefore, the following basic requirements must be met.
1.2.1 System requirements
1.2.2 System hydraulic oil requirements
According to the different ambient temperature and usage, the oil used should have good viscosity-temperature performance, good defoaming properties, anti-oxidation, anti-rust, high flash point, etc. During the operation of the motor, its viscosity is between (25-70)*10-6m2/s, and the water, alkali and mechanical impurities in the oil must not exceed the allowable value.
2. Motor installation
Before installation, check whether the motor is damaged. The motor oil stored for a long time needs to be drained and rinsed to prevent the internal moving parts from sticking.
The motor mounting bracket must have sufficient rigidity to prevent shock and vibration during rotation.
The mounting bolts must be tightened evenly.
Connection method of drain pipe:
The BMR motor has two built-in check valves, and the leaked oil can return to the oil return pipe through the check valve
A) When the oil return pressure is ≤1Mpa, there is no need to connect the drain pipe;
B) When the oil return pressure is greater than 1Mpa, the drain pipe must be connected. (Drain pipe location diagram)
3. Use of the motor
3.1 Use of motor
4. Motor troubleshooting
The motor is a precision component, which needs to be installed, commissioned and repaired by professionals. Without our company's consent, it is not allowed to dismantle and repair it by yourself. If the user unit has the conditions for dismantling and inspection with the permission of our company, after reading the instructions carefully, you can dismantle and inspect it yourself, but you must pay attention to the following three points:
|Serial number||Fault phenomenon||The Reason||Exclude|
|1||The motor does not rotate||Hydraulic pump does not start||Turn on the hydraulic pump|
|Insufficient oil in the tank||oil|
|Directional valve in neutral||Open the directional valve|
|System overflow valve fully open||The system pressure is adjusted to the specified value|
|Motor torque is not enough||Replace the motor|
|2||There is abnormal noise when the motor is running||There is air in the hydraulic system||Find out the reason for the intake air and discharge the air in the oil|
|Vacuum||Increase fuel supply|
|Motor failure||Replace the motor|
|Support bearing is broken||Replace bearing|
|3||Motor leakage||Damaged seal||Replace the seal|
|Parts have pores, trachoma, cracks, etc.||Replacement parts|
|4||Motor heat||Hydraulic oil temperature is too high||Increase cooling capacity|
|Low motor efficiency||Replace wearing parts|
|Abnormal wear||Replace the motor|
|5||Increased oil leakage at the outer drain hole||Abnormal wear at the distribution shaft||Replacement parts|
|Wear of the needle column group of the cycloid wheel stator body|
5. Motor maintenance and post-processing
Regularly check the accessories in the hydraulic system, the accuracy of pressure gauges, thermometers, etc.
The manufacturer is not responsible for the consequences caused by the user not following the above recommendations or using the motor incorrectly.